# MACHINE DESIGN + MACHINE STRUCTURAL DESIGN

If you can't find the course description that you're looking for in the above list, please see the following instructions >>
Versione italiana
2022/2023
Teacher
ROBERTO TOVO
Credits
12
Didactic period
Primo Semestre
SSD
ING-IND/14

#### Training objectives

------------------------------------------------------------
Modulo: 006495_M - ELEMENTI COSTRUTTIVI DELLE MACCHINE
------------------------------------------------------------
The objective of the course is giving some basic concepts about mechanical design and spurring students to use common mechanical formulae for machine design based on simple structural model.

------------------------------------------------------------
Modulo: 48792_M - COSTRUZIONE DI MACCHINE
------------------------------------------------------------
The objective of the course is giving some basic concepts about mechanical design and spurring students to use common mechanical formulae for machine design based on simple structural model.

#### Prerequisites

------------------------------------------------------------
Modulo: 006495_M - ELEMENTI COSTRUTTIVI DELLE MACCHINE
------------------------------------------------------------
In order to understand the lesson, the students should remember the basic concepts of these courses: Statics, Machines Design, Mechanics of Machines

------------------------------------------------------------
Modulo: 48792_M - COSTRUZIONE DI MACCHINE
------------------------------------------------------------
In order to understand the lesson, the students should remember the basic concepts of these courses: Statics, Machines Design, Mechanics of Machines

#### Course programme

------------------------------------------------------------
Modulo: 006495_M - ELEMENTI COSTRUTTIVI DELLE MACCHINE
------------------------------------------------------------
The course of Elements of machine design is developed in 60 hours of lessons and can be diveded into six thematic areas:
1) shafts and axles, shaft design (mechanical sketch and stiffness) (8 hours)
2) Couplings with parallel side keys,pins shaft, contact stresses (8 hours)
3) Types of lubrification,viscosity,Petroff's equation, Bearing Types, Bearing design, Ball bearing, Bearing Selection, Bearing Life, Shaft and Housing Design, (10 hours)
4)gears, nomenclature, tooth systems, force analysis, design of a gear, fatigue with Lewis equation, contact stresses ((10 hours)
5) belts, Flat belts, friction, equilibrium equations, bending, centrifugal force, flat-and rounded-belt driver, V belts, design procedure (12 hours)
6) Design of a power transmission between parallen schafts (12 hours)

Best practices for use of machine elements such as
Use of electronic sheet for design and drafting technical reports.

------------------------------------------------------------
Modulo: 48792_M - COSTRUZIONE DI MACCHINE
------------------------------------------------------------
The course of Elements of machine design is developed in 60 hours of lessons and can be diveded into six thematic areas:
1) shafts and axles, shaft design (mechanical sketch and stiffness) (8 hours)
2) Couplings with parallel side keys,pins shaft, contact stresses (8 hours)
3) Types of lubrification,viscosity,Petroff's equation, Bearing Types, Bearing design, Ball bearing, Bearing Selection, Bearing Life, Shaft and Housing Design, (10 hours)
4)gears, nomenclature, tooth systems, force analysis, design of a gear, fatigue with Lewis equation, contact stresses ((10 hours)
5) belts, Flat belts, friction, equilibrium equations, bending, centrifugal force, flat-and rounded-belt driver, V belts, design procedure (12 hours)
6) Design of a power transmission between parallen schafts (12 hours)

Best practices for use of machine elements such as
Use of electronic sheet for design and drafting technical reports.

#### Didactic methods

------------------------------------------------------------
Modulo: 006495_M - ELEMENTI COSTRUTTIVI DELLE MACCHINE
------------------------------------------------------------
The course is organized as follows:
lectures on all topics of the course and
classroom exercises on previously treated arguments.
During the course the student will make a design of a power transmission. The report and the mechanical drawing will be considered for the oral session of the exam.

------------------------------------------------------------
Modulo: 48792_M - COSTRUZIONE DI MACCHINE
------------------------------------------------------------
The course is organized as follows:
lectures on all topics of the course and
classroom exercises on previously treated arguments.
During the course the student will make a design of a power transmission. The report and the mechanical drawing will be considered for the oral session of the exam.

#### Learning assessment procedures

The exam is divided into two parts: written and oral.
The written exam lasts 3 hours and includes exercises of arguments during the course.
Who will score at least 18 points in the written will be permitted to perform the oral session.
In the oral session it will be evaluated the student for his ability to link and compare different aspects covered during the course.
If the oral session is sufficient, the final score will take into account the previous score and the quality of the report of the individual project.

#### Reference texts

------------------------------------------------------------
Modulo: 006495_M - ELEMENTI COSTRUTTIVI DELLE MACCHINE
------------------------------------------------------------
Mainly class notes and photocopies available at the copy center. Furhter information it will be found in:

Progetto e Costruzione di Macchine - Joseph E. Shigley, Charles R. Mischke, Richard G. Budynas, McGraw-Hill, 2005

Fondamenti della progettazione dei componenti delle macchine, R. C. Juvinall, K.M. Marshek, Edizioni ETS, Pisa, 2001

------------------------------------------------------------
Modulo: 48792_M - COSTRUZIONE DI MACCHINE
------------------------------------------------------------
Mainly class notes and photocopies available at the copy center. Furhter information it will be found in:

Progetto e Costruzione di Macchine - Joseph E. Shigley, Charles R. Mischke, Richard G. Budynas, McGraw-Hill, 2005

Fondamenti della progettazione dei componenti delle macchine, R. C. Juvinall, K.M. Marshek, Edizioni ETS, Pisa, 2001